幕墻鋁掛件施工過程（1）面板安裝：將事先加工好的面板按照設計院提供的排版圖懸掛于龍骨之上，面板與龍骨間用干掛纖維水泥壓力板配套鋁掛件連接，先將同一水平層纖維水泥壓力板輕掛在龍骨上，通過上下貫通鋼線及水平通線先調整好面板的水平與垂直度，再檢查板縫，板縫寬應按設計要求，板縫寬度均勻，滿足要求后，將配套鋁掛件上的20mm長，6mm粗不銹鋼螺絲擰緊后進行上層板材安裝。 （2）板縫處理：按照設計圖紙意圖，東側整面墻體纖維水泥壓力板板縫不做任何處理，采取明縫留設（豎縫寬20mm，橫縫寬10mm）。為此就要求在之前的施工過程中必須加強縫的水平、垂直檢測、確保橫平豎直。 （3）獨立柱處理：獨立柱轉角處陽角采用45°倒角對拼，打磨光滑，柱朝向走廊部位結構面采用滿粘法。45°斜角對拼縫隙采用纖維水泥壓力板粉末加膠填縫，外刷兩遍纖維水泥壓力板專用涂料。縫隙處壓力板粉末填縫時要注意填縫均勻、飽滿。 　　（4）清理表面，刷置面劑：用棉絲將纖維水泥壓力板擦凈，若有膠或其他粘結牢固的雜物，可用開刀輕輕鏟除，用棉絲沾丙酮擦至干凈。罩面劑按配合比在刷前半小時對好，注意區別底漆和面漆，分階段操作。配置罩面劑要攪勻，防止成膜時不勻。涂刷時要用羊毛刷，沾漆不宜過多，防止流劑，盡量少回刷，以免有刷痕，要求無氣泡、不漏刷，刷的平整要有光澤。