幕墻鋁掛件施工介紹　　（1）基層準備：清理預做干掛纖維水泥壓力板飾面的基層表面，同時進行吊直、套方、找規矩，彈出垂直線和水平線。并根據設計圖紙和實際需要彈出安裝纖維水泥壓力板龍骨的位置線和分塊線。將墻體表邊塵土、污垢清掃干凈。 　　（2）掛線：按設計圖紙要求，纖維水泥壓力板龍骨安裝前要事先用經緯儀打出大角兩個面的豎向控制線，彈在離大角20cm的位置上，以便隨時檢查垂直掛線的準確性，保證順利安裝。豎向掛線宜用∮1.0-∮1.2的鋼絲為好，下邊沉鐵重量為8-10kg，上端掛在專用的掛線角鋼架上，角鋼架用膨脹螺栓固定在中庭南北大角的頂端，一定要掛在牢固、準確、不易碰動的地方，并要注意保護和經常檢查。并在控制線的上、下做出標記。 　　（3）龍骨安裝：預先用∮8脹栓在結構面上固定50×50×4角鋼（角鋼上帶可調節孔），角鋼及角鋼上50×50×3.5豎向方鋼管水平間距為800mm。豎向方鋼管安裝時，必須通過從上往下吊的鋼線進行復核，以檢測其垂直度。方鋼管安裝完畢之后，安裝連接角鋼及橫向鋁龍骨，橫向鋁龍骨豎向間距為600mm。角鋼與方鋼管及橫龍骨之間連接均采用∮10螺栓。龍骨安裝完之后用紅外線水平儀檢測橫向鋁龍骨是否水平，掉鋼線檢測其是否垂直，過程中發現問題及時調整，將誤差控制在最小。